Dimensions
With TeSys U Combination (Non Reversing Power Base)
Mounting on symetrical (35 mm) rail with power connector between ATS and TeSys U.
With TeSys U Combination (Non Reversing or Reversing Power Base)
Side by side mounting
ATSU01N212LT
$894.89
Special Order-Generally ships in 14 to 21 Business Days
SKU
ATSU01N212LT
soft starter for asynchronous motor - ATSU01 - 12 A - 200..480V - 2.2..5.5 KW
Main
- Range of product
- Altistart U01 and TeSys U
- Product or component type
- Soft starter
- Product destination
- Asynchronous motors
- Product specific application
- Simple machine
- Device short name
- ATSU01
- Network number of phases
- 3 phases
- [Us] rated supply voltage
- 200...480 V - 10...10 %
- Motor power kW
- 2.2 kW 3 phases 230 V
5.5 kW 3 phases 400 V
3 kW 3 phases 230 V - Motor power hp
- 3 hp 3 phases 230 V
7.5 hp 3 phases 460 V - IcL starter rating
- 12 A
- Utilisation category
- AC-53B EN/IEC 60947-4-2
- Current consumption
- 65 mA
- Type of start
- Start with voltage ramp
- Power dissipation in W
- 1.5 W at full load and at end of starting
121.5 W in transient state
Complementary
- Assembly style
- With heat sink
- Function available
- Integrated bypass
- Supply voltage limits
- 180...528 V
- Supply frequency
- 50...60 Hz - 5...5 %
- Network frequency
- 47.5...63 Hz
- Output voltage
- <= power supply voltage
- [Uc] control circuit voltage
- 24 V DC +/- 10 %
- Starting time
- 1 s 100
10 s 10
5 s 20
Adjustable from 1 to 10 s - Deceleration time symb
- Adjustable from 1 to 10 s
- Starting torque
- 30...80 % of starting torque of motor connected directly on the line supply
- Discrete input type
- Logic LI1, LI2, BOOST stop, run and boost on start-up functions <= 8 mA 27 kOhm
- Discrete input voltage
- 24...40 V
- Input output isolation
- Galvanic between power and control
- Discrete input logic
- Positive LI1, LI2, BOOST < 5 V and <= 0.2 mA > 13 V >= 0.5 mA
- Discrete output current
- 2 A DC-13
3 A AC-15 - Discrete output type
- Open collector logic LO1 end of starting signal
Relay outputs R1A, R1C NO - Discrete output voltage
- 24 V 6...30 V open collector logic
- Minimum switching current
- 10 mA 6 V DC relay outputs
- Maximum switching current
- 2 A 30 V DC inductive cos phi = 0.5 20 ms relay outputs
2 A 250 V AC AC-15 inductive cos phi = 0.5 20 ms relay outputs - Maximum switching voltage
- 440 V relay outputs
- Display type
- 1 LED green starter powered up
1 LED yellow nominal voltage reached - Tightening torque
- 0.5 N.m
1.9...2.5 N.m - Electrical connection
- 4 mm screw clamp terminal rigid 1 1...10 mm² AWG 8 power circuit
Screw connector rigid 1 0.5...2.5 mm² AWG 14 control circuit
4 mm screw clamp terminal rigid 2 1...6 mm² AWG 10 power circuit
Screw connector rigid 2 0.5...1 mm² AWG 17 control circuit
Screw connector flexible with cable end 1 0.5...1.5 mm² AWG 16 control circuit
4 mm screw clamp terminal flexible without cable end 1 1.5...10 mm² AWG 8 power circuit
Screw connector flexible without cable end 1 0.5...2.5 mm² AWG 14 control circuit
4 mm screw clamp terminal flexible with cable end 2 1...6 mm² AWG 10 power circuit
4 mm screw clamp terminal flexible without cable end 2 1.5...6 mm² AWG 10 power circuit
Screw connector flexible without cable end 2 0.5...1.5 mm² AWG 16 control circuit - Marking
- CE
- Operating position
- Vertical +/- 10 degree
- Height
- 234 mm
- Width
- 45 mm
- Depth
- 150 mm
- Product weight
- 0.34 kg
- Power range
- 2.2...3 kW at 200...240 V 3 phases
4...6 kW at 380...440 V 3 phases - Motor starter type
- Soft starter
Environment
- Electromagnetic compatibility
- Damped oscillating waves level 3 IEC 61000-4-12
Electrostatic discharge level 3 IEC 61000-4-2
Immunity to electrical transients level 4 IEC 61000-4-4
Immunity to radiated radio-electrical interference level 3 IEC 61000-4-3
Voltage/current impulse level 3 IEC 61000-4-5
Conducted and radiated emissions level B CISPR 11
Conducted and radiated emissions level B IEC 60947-4-2
EMC immunity EN 50082-2
Harmonics IEC 1000-3-2
Harmonics IEC 1000-3-4
Conducted and radiated emissions level 3 IEC 61000-4-6
Immunity to conducted interference caused by radio-electrical fields IEC 61000-4-11
EMC immunity EN 50082-1 - Standards
- EN/IEC 60947-4-2
- Product certifications
- CCC
CSA
C-Tick
UL - IP degree of protection
- IP20
- Pollution degree
- 2 EN/IEC 60947-4-2
- Vibration resistance
- 1.5 mm peak to peak 3...13 Hz EN/IEC 60068-2-6
1 gn 13...150 Hz EN/IEC 60068-2-6 - Shock resistance
- 15 gn 11 ms EN/IEC 60068-2-27
- Relative humidity
- 5...95 % without condensation or dripping water EN/IEC 60068-2-3
- Ambient air temperature for operation
- -10...40 °C without derating
40...50 °C with current derating of 2 % per °C - Ambient air temperature for storage
- -25...70 °C EN/IEC 60947-4-2
- Operating altitude
- <= 1000 m without derating
> 1000 m with current derating of 2.2 % per additional 100 m
Contractual warranty
- Warranty period
- 18 months
Write Your Own Review
Frequently Asked Questions and Answers
- Which power phases are controlled by Altistart 01 Soft-Starter?
The power phases that are controlled by Altistart 01 Soft-Starter are as follows: In N1 Range of Altistart 01 Soft-Starter only 1 Phase is controlled and that is L1, L2 and L3 are uncontrolled. In N2 Range of Altistart 01 Soft-Starter only 2 Phases are controlled and that is L2 and L3, L1 is uncontrolled.
Read more - Do the Altistart 01 soft-starters have any available spare parts?
Issue: Do the Altistart 01 soft-starters have any available spare parts? Product Line: Altistart 01 Environment: All serial numbers for Altistart 01 Cause: N/A Resolution: There are no spare parts available for the Altistart 01 soft-starters
Read more - What are the dimensions for the ats01n230ly and ats01n244ly?
Issue: What are the dimensions for the ATS01N230LY and ATS01N244LY? Product Line: Altistart 01 Environment: All Cause: N/A Resolution: Both units have the same dimensions: 4.96 (126 mm) inches deep 5.75 (146 mm) inches tall 7.09 (180 mm) inches wide
Read more - Does the ats01 softstart require external thermal overload protection?
Issue: Does the ATS01 softstart require external thermal overload protection? Product Line: ATS01, Altistart 01 Environment: All Cause: N/A Resolution: The ATS01 softstart does require an external overload thermal protection for the motor. It also requires a starter or a contactor to be used at the line of the softstart.
Read more - What is the replacement for the High HP ats01n softstarters?
Issue: Wants to order the ATS01N230LY, ATS01N244LY, ATS01N272LY or ATS01N285LY Product line: ATS01, Altistart 01, High HP Environment: All models Cause: The launch of the ATS22 in 2011 caused the High HP units to become redundant. Resolution: The ATS01 High HP units were replaced with the ATS22 units. These are functional replacements only. The ATS01 had no overload protection, an internal power supply and simple dial adjustments. The ATS22 will require external 120V or 230V po...
Read more
Catalogue
CAD
Certificate
End of life manual
Dimensions Drawings
Connections and Schema
Power Wiring
(1)
TeSys U
A1 :
Soft start/soft stop unit
QF1 :
TeSys U controller-starter
CU :
TeSys U control unit
With Reversing Unit
(1)
TeSys U with reversing unit
A1 :
Soft start/soft stop unit
QF1 :
TeSys U controller-starter
CU :
TeSys U control unit
Control Wiring
A1 :
Soft start/soft stop unit
R1A, R1C :
Relay output NO
COM :
Commun
LI1, LI2 :
Logic inputs (stop and run functions)
BOOST :
Logic input (boost on start-up function)
LO1 :
Logic output
Technical Description
Functional Diagram Automatic 2-wire Control
Without Deceleration
Us :
Power supply voltage
LED 1 :
Green LED
LI2 :
Logic input
S1 :
Pushbutton
LED 2 :
Yellow LED
Um :
Motor voltage
t1 :
Acceleration time can be controlled by a potentiometer
U1 :
Starting time can be controlled by a potentiometer
With and without Deceleration
Us :
Power supply voltage
LED 1 :
Green LED
LI2 :
Logic input
S1, S2 :
Pushbuttons
LO1 :
Logic output
LED 2 :
Yellow LED
Um :
Motor voltage
t1 :
Acceleration time can be controlled by a potentiometer
t2 :
Deceleration time can be controlled by a potentiometer
U1 :
Starting time can be controlled by a potentiometer
Functional Diagram Automatic 3-wire Control
Without Deceleration
Us :
Power supply voltage
LED 1 :
Green LED
S1, S2 :
Pushbuttons
LI2 :
Logic input
LO1 :
Logic output
LED 2 :
Yellow LED
Um :
Motor voltage
t1 :
Acceleration time can be controlled by a potentiometer
U1 :
Starting time can be controlled by a potentiometer
With Deceleration
Us :
Power supply voltage
LED 1 :
Green LED
S1, S2 :
Pushbuttons
LI1, LI2 :
Logic inputs
LO1 :
Logic output
LED 2 :
Yellow LED
Um :
Motor voltage
t1 :
Acceleration time can be controlled by a potentiometer
© 2018 Switchboard in a Box. All Rights Reserved. Design & Developed by Shaligram Infotech