VW3A4558
line choke - 0.155 mH - 184 A - 3 phases - 220 W - for variable speed drive
- Range of product
- Altivar
- Product or component type
- Line choke
- Product compatibility
- ATV61HD90N4D - line choke - 1 per drive
ATV61WD90N4 - line choke - 1 per drive
ATV61WD90N4C - line choke - 1 per drive
ATV71HD75N4 - line choke - 1 per drive
ATV71WD75N4 - line choke - 1 per drive - Network number of phases
- Three phase
- Range compatibility
- Altivar 61
Altivar 71 - Device application
- Reduction of current harmonics
- Value of inductance
- 0.155 mH
- [In] rated current
- 184 A
- Saturation current
- 370 A
- Thermal losses
- 220 W
- Electrical connection
- Bare wires, Ø = 9 mm
- Supply frequency
- 50...60 Hz
- Max current
- 1.65 x nominal current for 60 s
- Voltage drop at rated load
- 5 %
- Electrical insulation class
- Class F
- Clearance distance
- 5.5 mm conforming to IEC 60664
- Leakage distance
- 11.5 mm conforming to IEC 60664
- Product weight
- 31 kg
- Width
- 280 mm
- Height
- 330 mm
- Depth
- 210 mm
- Standards
- EN 50178
IEC 60076 (with HD398)
VDE 0160 level 1 - IP degree of protection
- IP00 (choke)
IP00 (terminals) - Environmental characteristic
- 3B1 conforming to IEC 721-3-3
3C2 conforming to IEC 721-3-3
3S1 conforming to IEC 721-3-3 - Pollution degree
- 2 conforming to EN 50178
- Vibration resistance
- 1.5 mm peak to peak (f = 3...13 Hz) conforming to IEC 60068-2-6
1 gn (f = 13...200 Hz) conforming to IEC 60068-2-6 - Shock resistance
- 15 gn for 11 ms conforming to IEC 60068-2-27
- Relative humidity
- 0...95 %
- Ambient air temperature for operation
- > 45...< 55 °C with current derating of 2 % per °C
0...45 °C without current derating - Ambient air temperature for storage
- -25...70 °C
- Operating altitude
- 1000...3000 m with current derating 1 % per 100 m
- Warranty period
- 18 months
Frequently Asked Questions and Answers
- What supplies the power to vw3a3401 encoder interface card fitted on Altivar 71?
The encoder interface card VW3A3401 uses an internal 5VDC supply from the drive control block. The interface card supplies 5VDC to the encoder RS422 with maximum current available up to 200mA.
Read more - When does the Drive Overheat Fault (OHF) occur in Altivar 71 Drives.
The Drive Overheat Fault (OHF) indicates that the heat sink temperature has crossed the temperature threshold. This is the information from the temperature sensor located on the heat sink, near the transistor module. When the Thermal Heat Dissipation (THD) is greater than 118% it trips in OHF. 118% is approximately 100 Deg Centigrade temperature on the heat sink. The main causes for the occurrence of this fault are: 1. Excessive ambient temperature. (Provide proper air cooling of the control roo...
Read more - Altivar 61/71 what is the recommended corrective action when the motor runs in reverse with a run forward command?
Issue: The motor is running backwards with a forward run command on the drive. Product line: Altivar ATV61 and ATV71 Environment: All models, all serial numbers Cause: The phase rotation is inverted coming out of the drive going to the motor. Resolution: Option 1: To correct the motor rotation swap two motor leads on the drive output terminals. Option 2: Go in the simple start menu 1.1 find output phase rotation change it from ABC to ACB. Refer to the ATV61 and ATV71 programm...
Read more - What does ramp increment mean for the Altivar 61/71?
Issue: What does ramp increment mean for the Altivar 61/71? Product Line: Altivar 61, Altivar 71 Environment: All serial numbers Cause: N/A Resolution: Ramp increment is a parameter that will change the resolution of the listed parameters: see below Inr M [Ramp increment] 0.01 - 0.1 - 1 0.1 0.01 [0.01]: Ramp up to 99.99 seconds 0.1 [0.1]: Ramp up to 999.9 seconds 1 [1]: Ramp up to 9,000 s...
Read more - Will the relay output, assigned to No Drive Fault, change states on a fault if Auto restart is set to yes on VFD?
Issue: Will the relay output, assigned to No Drive Fault, change states on a fault if Auto restart is set to yes? Product Line: Altivar 61 Altivar 71 ATV61 ATV71 Environment: All Cause: Define the No Drive Fault relay relationship with Auto restart function. Resolution: The relay assigned to No Drive Fault will not change states on a fault, if Auto restart is set to YES, until the max restart time is depleted and the fault still exists.
Read more
