Contacts type and composition: 1 C/O timed contact, cadmium free
Time delay type: A

Ac

At

Aw

C

D

Di

H

Ht

W

Act

Ct

Dw

Hw

Wt

Dt

Dit

Diw
Time delay range: 0.05...1 s

0.3...3 s

1...10 s

10...100 s

3...30 h

3...30 min

3...30 s

30...300 h

30...300 min

30...300 s
Control type: Rotary knob

Diagnostic button

External potentiometer
[Us] rated supply voltage: 24...240 V AC/DC at 50/60 Hz
Input voltage: <= 2.4 V
Voltage range: 0.85...1.1 Us
Supply frequency: 50...60 Hz (+/- 5 %)
Connections - terminals: Screw terminals : 1 x 0.5...1 x 3.3 mm², AWG 20...AWG 12 solid cable without cable end

Screw terminals : 2 x 0.5...2 x 2.5 mm², AWG 20...AWG 14 solid cable without cable end

Screw terminals : 1 x 0.2...1 x 2.5 mm², AWG 24...AWG 14 flexible cable with cable end

Screw terminals : 2 x 0.2...2 x 1.5 mm², AWG 24...AWG 16 flexible cable with cable end
Tightening torque: 0.6...1 N.m conforming to IEC 60947-1
Housing material: Self-extinguishing
Repeat accuracy: +/- 0.5 % conforming to IEC 61812-1
Temperature drift: +/- 0.05 %/°C
Voltage drift: +/- 0.2 %/V
Setting accuracy of time delay: +/- 10 % of full scale at 25 °C conforming to IEC 61812-1
Minimum pulse duration: 100 ms (with load in parallel)

30 ms
Insulation resistance: 100 MOhm at 500 V DC conforming to IEC 60664-1
Reset time: 120 ms (on de-energisation)
Immunity to microbreaks: <= 10 ms
Power consumption in VA: 3 VA at 240 V AC
Power consumption in W: 1.5 W at 240 V DC
Switching capacity in VA: 2000 VA
Minimum switching current: 10 mA 5 V DC
Maximum switching current: 8 A
Maximum switching voltage: 250 V AC
Electrical durability: 100000 cycles for 8 A at 250 V AC-1

100000 cycles for 2 A at 24 V DC-1
Mechanical durability: 10000000 cycles
[Uimp] rated impulse withstand voltage: 5 kV for 1.2...50 µs conforming to IEC 60664-1
Delay response: < 100 ms
Creepage distance: 4 kV/3 conforming to IEC 60664-1
Overvoltage category: III conforming to IEC 60664-1
Safety reliability data: MTTFd = 205.4 years

B10d = 190000
Mounting position: Any position
Mounting support: 35 mm DIN rail conforming to EN/IEC 60715
Status LED: Green LED backlight (steady) for dial pointer indication

Yellow LED (steady) for output relay energised

Yellow LED (fast flashing) for timing in progress and output relay de-energised

Yellow LED (slow flashing) for timing in progress and output relay energised
Width: 22.5 mm
Product weight: 0.1 kg

Environment

Dielectric strength: 2.5 kV for 1 mA/1 minute at 50 Hz between relay output and power supply with basic insulation conforming to IEC 61812-1
Standards: IEC 61812-1

UL 508
Directives: 2004/108/EC - electromagnetic compatibility

2006/95/EC - low voltage directive
Product certifications: CCC

CE

CSA

GL

UL

RCM

EAC

China RoHS
Ambient air temperature for operation: -20...60 °C
Ambient air temperature for storage: -40...70 °C
IP degree of protection: IP20 (terminals) conforming to IEC 60529

IP40 (housing) conforming to IEC 60529

IP50 (front face) conforming to IEC 60529
Pollution degree: 3 conforming to IEC 60664-1
Vibration resistance: 20 m/s² (f = 10...150 Hz) conforming to IEC 60068-2-6
Shock resistance: 15 gn (not operating) (duration = 11 ms) conforming to IEC 60068-2-27

5 gn (in operation) (duration = 11 ms) conforming to IEC 60068-2-27
Relative humidity: 95 % at 25...55 °C
Electromagnetic compatibility: Fast transients immunity test (test level: 1 kV, level 3 - capacitive connecting clip) conforming to IEC 61000-4-4

Surge immunity test (test level: 1 kV, level 3 - differential mode) conforming to IEC 61000-4-5

Surge immunity test (test level: 2 kV, level 3 - common mode) conforming to IEC 61000-4-5

Electrostatic discharge (test level: 6 kV, level 3 - contact discharge) conforming to IEC 61000-4-2

Electrostatic discharge (test level: 8 kV, level 3 - air discharge) conforming to IEC 61000-4-2

Radiated radio-frequency electromagnetic field immunity test (test level: 10 V/m, level 3 - 80 MHz...1 GHz) conforming to IEC 61000-4-3

Conducted RF disturbances (test level: 10 V, level 3 - 0.15...80 MHz) conforming to IEC 61000-4-6

Fast transient bursts (test level: 2 kV, level 3 - direct contact) conforming to IEC 61000-4-4

Immunity to microbreaks and voltage drops (test level: 30 % - 500 ms) conforming to IEC 61000-4-11

Immunity to microbreaks and voltage drops (test level: 100 % - 20 ms) conforming to IEC 61000-4-11

Offer Sustainability

Sustainable offer status: Green Premium product
RoHS (date code: YYWW): Schneider Electric declaration of conformity
REACh: Reference not containing SVHC above the threshold
Product environmental profile: Product Environmental Profile
Product end of life instructions: End of Life Information

Write Your Own Review

Frequently Asked Questions and Answers

View all

Catalogue

Zelio Time Timing Relays catalog (pdf)

Instruction sheet

RE22... Timing relays, Instruction Sheet (pdf)

Certificate

UL Listed RE17, RE22, REXL, RE48A, RE88857, RE88865, RE88867, RENF22R2MMW (htm)

UL Listed RE17, RE22, REXL, RE48A, RE88857, RE88865, RE88867, RENF22R2MMW (htm)

Zelio Timer RE22 (pdf)

Declaration of conformity

EU DOC - Zelio Timer RE22 (pdf)

End of life manual

RE22... Timer Relay - Zelio Time, Product End-of-Life Instructions (pdf)

Marine certificate

GL Certificate RE22 (pdf)

Product environmental

RE22... Timing Relay - Zelio Time, Product Environmental Profile (pdf)

REACh Declaration

Multi-function Timing Relay - 0.05sâ€¦300h - 24â€¦240V AC/DC - 1C/O (pdf)

RoHs Declaration

Multi-function Timing Relay - 0.05sâ€¦300h - 24â€¦240V AC/DC - 1C/O (pdf)

Dimensions Drawings

Dimensions

Connections and Schema

Wiring Diagram

Technical Description

Function A: Power On-Delay

Description

On energisation of power supply, the timing period T starts. After timing, the output(s) R close(s).The second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST").

Function: 1 Output

Function: 2 Outputs

Function Ac: On-Delay & Off-Delay with Control Signal

Description

After energisation of power supply and energization of Y1 causes the timing period T to start.

At the end of this timing period, the output(s) R close(s).

When deenergization of Y1, the timing T starts.

At the end of this timing period T,the output(s) R revert(s) to its/their initial position.

The second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST").

Function: 1 Output

Function: 2 Outputs

Function Act: On-Delay & Off-Delay with Control Signal & With Pause / Summation Control

Description

After energisation of power supply and energization of Y1 causes the timing period T to start and the timing can be interrupted / paused each time X1 energizes.When the cumulative total of time periods elapsed reaches the pre-set value T, the output(s) R close(s).When deenergization of Y1, the timing T starts and the timing can be interrupted / paused each time X1 energizes. When the cumulative total of time periods elapsed reaches the pre-set value T, the output(s) R revert(s) to its/their initial position.The second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST").

Function: 1 Output

T =

t1 + t2 +â€¦

T =

t'1 + t'2 +â€¦

Function: 2 Outputs

T =

t1 + t2 +â€¦

T =

t'1 + t'2 +â€¦

Function At: Power On-Delay with Pause / Summation Control

Description

On energisation of power supply, the timing period T starts.Timing can be interrupted / paused each time X1 energizes.Except for RE17*, RE22R2AMU, RE22R2MMW, RE22R2MMU, RE22R2MJU, timing can be interrupted / paused each time Y1 energizes.When the cumulative total of time periods elapsed reaches the pre-set value T, the output(s) R close(s).The second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST").

Function: 1 Output with Pause / Summation Control

T =

t1 + t2 +â€¦

Function: 2 Outputs with Pause / Summation Control

T =

t1 + t2 +â€¦

Function: 1 Output with Retrigger / Restart Control

T =

t1 + t2 +â€¦

Function: 2 Outputs with Retrigger / Restart Control

T =

t1 + t2 +â€¦

Function Aw : Power On-Delay With Retrigger / Restart Control

Description

On energisation of power supply, the timing period T starts.At the end of the timing period T, the output(s) R close(s).Energization of Y1 makes the output(s) R open(s).Deenergization of Y1 restarts timing period T.At the end of timing period T, the output(s) R close(s).The second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST")

Function: 1 Output

Function: 2 Outputs

Function C: Off-Delay Relay with Control Signal

Description

After energisation of power supply and energization of Y1 causes output(s) R close(s). When Y1 deenergizes, timing T starts.At the end of this timing period T,the output(s) R revert(s) to its/their initial position.The second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST").

Function: 1 Output

Function: 2 Outputs

Function Ct: Off-Delay Relay with Control Signal & With Pause / Summation Control

Description

After energisation of power supply and energization of Y1 cause output(s) R close(s).When Y1 deenergizes, timing starts and the timing can be interrupted / paused each time X1 energizes. When the cumulative total of time periods elapsedreaches the pre-set value T, the output(s) R revert(s) to its/their initial state.The second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST").

Function: 1 Output

T =

t1 + t2 +â€¦

Function: 2 Outputs

T =

t1 + t2 +â€¦

Function D: Symmetrical Flashing Relay (Starting Pulse Off)

Description

On energisation of power supply, output(s) R starts at its/their initial state for timing duration T then change(s) to output(s) R close(s) for the same timing duration T.This cycle is repeated indefintely until power supply removal.Specially for RE17*, RE22R2AMU, RE22R2MMW, RE22R2MMU, RE22R2MJU,this D function can only be initiated by energizing Y1 permanently.The second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST").

Function: 1 Output

Function: 2 Outputs

Function: 1 Output with Retrigger / Restart Control

Function: 2 Output with Retrigger / Restart Control

Function Dt: Symmetrical Flashing Relay (Starting Pulse Off) & With Pause / Summation Control

Description

On energisation of power supply, output(s) R starts at its/their initial state for timing duration T and the timing can be interrupted / paused each time X1 energizes.When the cumulative total of time periods elapsed reaches the pre-set value T, then changes to output(s) R close(s).The output(s) R close state will remain for the same timing duration T and the timing can be interrupted / paused each time X1 energizes.When the cumulative total of time periods elapsed reaches the pre-set value T, the output(s) R revert(s) to its/their initial state.This cycle is repeated indefintely until power supply removal.The second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST").

Function: 1 Output

T =

t1 + t2 +â€¦

T =

t'1 + t'2 +â€¦

Function: 2 Outputs

T =

t1 + t2 +â€¦

T =

t'1 + t'2 +â€¦

Function DW: Symmetrical Flashing Relay (Starting Pulse Off) & With Retrigger / Restart Control

Description

Function: 1 Output

Function: 2 Outputs

Function Di: Symmetrical Flashing Relay (Starting Pulse On)

Description

On energisation of power supply, output(s) R starts at output(s) R close(s) for timing duration T then revert(s) to its/their initial state for the same timing duration T.This cycle is repeated indefintely until power supply removal.The second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST").

Function: 1 Output

Function: 2 Outputs

Function Dit: Symmetrical Flashing Relay (Starting Pulse On) & With Pause / Summation Control

Description

On energisation of power supply, output(s) R starts at output(s) R close(s) for timing duration T and the timing can be interrupted / paused each time X1 energizes.When the cumulative total of time periods elapsed reaches the pre-set value T, then revert(s) to its/their initial state.The output(s) R at initial state will remain for the same timing duration T and the timing can be interrupted / paused each time X1 energizes.When the cumulative total of time periods elapsed reaches the pre-set value T, the output(s) R change(s) to close state.This cycle is repeated indefintely until power supply removal.The second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST").

Function: 1 Output

T =

t1 + t2 +â€¦

T =

t'1 + t'2 +â€¦

Function: 2 Outputs

T =

t1 + t2 +â€¦

T =

t'1 + t'2 +â€¦

Function Diw: Symmetrical Flashing Relay (Starting Pulse On) & With Retrigger / Restart Control

Description

On energisation of power supply, output(s) R starts at output(s) R close(s) for timing duration T then revert(s) to its/their initial state for the same timing duration T.This cycle is repeated indefintely until power supply removal.At any state of the output(s) R when Y1 energizes, the output(s) R will revert to its/their initial state and followed by Y1 deenergizes then restarts the same operation as described at the beginning.The second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST").

Function: 1 Output

Function: 2 Outputs

Function H: Interval Relay

Description

On energisation of power supply, output(s) R close(s) and timing period T starts.At the end of the timing period T, the output(s) R revert(s) to its/their initial state.The second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST").

Function: 1 Output

Function: 2 Outputs

Function Ht: Interval Relay & With Pause / Summation Control

Description

On energisation of power supply, output(s) R close(s) and timing period T starts.The timing can be interrupted / paused each time X1 energizes. When the cumulative total of time periods elapsed reaches the pre-set value T, the output(s) R revert(s) to its/their initial stateReenergization of X1 will also cause output(s) R close(s) if the time has elapsed and restart the same operation as described at the beginning.Except for RE17*, RE22R2AMU, RE22R2MMW, RE22R2MMU, RE22R2MJU, timing can be interrupted / paused each time Y1 energizes.The second output (R2) can be either timed (when set to "TIMED" or instantaneous (when set to "INST").

Function: 1 Output

T =

t1 + t2 +â€¦

Function: 2 Outputs

T =

t1 + t2 +â€¦

Function: 1 Output with Retrigger / Restart Control

T =

t1 + t2 +â€¦

Function: 2 Output with Retrigger / Restart Control

T =

t1 + t2 +â€¦

Function Hw: Interval Relay & with Retrigger / Restart Control

Description

On energisation of power supply, output(s) R close(s) and timing period T starts.At the end of the timing period T, the output(s) R revert(s) to its/their initial state.At any state of the output(s) R when Y1 energizes followed by deenergizes, the output(s) R close(s) then restarts the same operation as described at the beginning.The second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST").

Function: 1 Output

Function: 2 Outputs

Function W: Interval Relay with Control Signal Off

Description

After energisation of power supply and on energization of Y1 following by denergization of Y1, the output(s) R close(s) and starts the timing T.At the end of the timing period, the output(s) R revert(s) to its/their initial state.The second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST").

Function: 1 Output

Function: 2 Outputs

Function Wt: Interval Relay with Control Signal Off & with Pause / Summation Control

Description

After energisation of power supply and on energization of Y1 following by denergization of Y1, the output(s) R close(s) and starts the timing T.Timing can be interrupted / paused each time X1 energizes.When the cumulative total of time periods elapsed reaches the pre-set value T, the output(s) R revert(s) to its/their initial state.The second output (R2) can be either timed (when set to "TIMED") or instantaneous (when set to "INST").

Function: 1 Output

T =

t1 + t2 +â€¦

Function: 2 Outputs

T =

t1 + t2 +â€¦

Legend

Relay de-energised

Relay energised

Output open

Output closed

U -

Supply

R1/R2 -

2 timed outputs

X1 -

Pause / Summation control

Y1 -

Retrigger / Restart control

R2 inst. -

The second output is instantaneous if the right position is selected

T -

Timing period

RE22R1MYMR

Multi-function Timing Relay - 0.05s…300h - 24…240V AC/DC - 1C/O

Frequently Asked Questions and Answers

Dimensions Drawings

Connections and Schema

Technical Description

Login

Create New Account

Forgot Password

The information below is required for social login