ATV12HU15M3

$728.73
Special Order-Generally ships in 14 to 21 Business Days
SKU
ATV12HU15M3

variable speed drive ATV12 - 1.5kW - 2hp - 200..240V - 3ph - with heat sink

Main
Range of product
Altivar 12
Product or component type
Variable speed drive
Product destination
Asynchronous motors
Product specific application
Simple machine
Assembly style
With heat sink
Component name
ATV12
Quantity per set
Set of 1
EMC filter
Without EMC filter
Built-in fan
With
Network number of phases
3 phases
[Us] rated supply voltage
200...240 V - 15...10 %
Motor power kW
1.5 kW
Motor power hp
2 hp
Communication port protocol
Modbus
Line current
11.1 A 200 V

9.3 A 240 V
Speed range
1...20
Transient overtorque
150...170 % of nominal motor torque depending on drive rating and type of motor
Asynchronous motor control profile
Quadratic voltage/frequency ratio

Sensorless flux vector control

Voltage/frequency ratio (V/f)
IP degree of protection
IP20 without blanking plate on upper part
Noise level
50 dB
Complementary
Supply frequency
50/60 Hz +/- 5 %
Connector type
1 RJ45 Modbus on front face
Physical interface
2-wire RS 485 Modbus
Transmission frame
RTU Modbus
Transmission rate
4800 bit/s

9600 bit/s

19200 bit/s

38400 bit/s
Number of addresses
1...247 Modbus
Communication service
Read holding registers (03) 29 words

Write single register (06) 29 words

Write multiple registers (16) 27 words

Read/write multiple registers (23) 4/4 words

Read device identification (43)
Prospective line Isc
<= 5 kA
Continuous output current
7.5 A 4 kHz
Maximum transient current
11.2 A 60 s
Speed drive output frequency
0.5...400 Hz
Nominal switching frequency
4 kHz
Switching frequency
2...16 kHz adjustable

4...16 kHz with derating factor
Braking torque
Up to 70 % of nominal motor torque without braking resistor
Motor slip compensation
Adjustable

Preset in factory
Output voltage
200...240 V 3 phases
Electrical connection
Terminal 5.5 mm² AWG 10 L1, L2, L3, U, V, W, PA, PC
Tightening torque
1.2 N.m
Insulation
Electrical between power and control
Supply
Internal supply for reference potentiometer 5 V DC 4.75...5.25 V 10 mA overload and short-circuit protection

Internal supply for logic inputs 24 V DC 20.4...28.8 V 100 mA overload and short-circuit protection
Analogue input number
1
Analogue input type
Configurable voltage AI1 0...10 V 30 kOhm

Configurable voltage AI1 0...5 V 30 kOhm

Configurable current AI1 0...20 mA 250 Ohm
Discrete input number
4
Discrete input type
Programmable LI1...LI4 24 V 18...30 V
Discrete input logic
Negative logic (sink) > 16 V < 10 V 3.5 kOhm

Positive logic (source) 0...< 5 V > 11 V
Sampling duration
20 ms +/- 1 ms logic input

10 ms analogue input
Linearity error
+/- 0.3 % of maximum value analogue input
Analogue output number
1
Analogue output type
Software-configurable voltage AO1 0...10 V 470 Ohm 8 bits

Software-configurable current AO1 0...20 mA 800 Ohm 8 bits
Discrete output number
2
Discrete output type
Logic output LO+, LO-

Protected relay output R1A, R1B, R1C 1 C/O
Minimum switching current
5 mA 24 V DC logic relay
Maximum switching current
2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay

2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay

3 A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay

4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay
Acceleration and deceleration ramps
Linear from 0 to 999.9 s

S

U
Braking to standstill
By DC injection <= 30 s
Protection type
Against input phase loss in three-phase

Thermal motor protection via the drive by continuous calculation of I²t

Line supply overvoltage

Line supply undervoltage

Overcurrent between output phases and earth

Overheating protection

Short-circuit between motor phases
Frequency resolution
0.1 Hz display unit

Converter A/D, 10 bits analog input
Time constant
20 ms +/- 1 ms for reference change
Marking
CE
Operating position
Vertical +/- 10 degree
Height
143 mm
Width
105 mm
Depth
131.2 mm
Product weight
1.2 kg
Specific application
Commercial equipment
Discrete and process manufacturing
Commercial equipment : mixer

Commercial equipment : other application

Textile : ironing
Motor starter type
Variable speed drive
Environment
Electromagnetic compatibility
Immunity to conducted disturbances level 3 EN/IEC 61000-4-6

Surge immunity test level 3 EN/IEC 61000-4-5

Voltage dips and interruptions immunity test EN/IEC 61000-4-11

Electrical fast transient/burst immunity test level 4 EN/IEC 61000-4-4

Electrostatic discharge immunity test level 3 EN/IEC 61000-4-2

Radiated radio-frequency electromagnetic field immunity test level 3 EN/IEC 61000-4-3
Electromagnetic emission
Radiated emissions environment 1 category C2 EN/IEC 61800-3 2...16 kHz shielded motor cable

Conducted emissions with additional EMC filter environment 1 category C1 EN/IEC 61800-3 4...12 kHz shielded motor cable 5 m

Conducted emissions with additional EMC filter environment 1 category C2 EN/IEC 61800-3 4...12 kHz shielded motor cable 20 m

Conducted emissions with additional EMC filter environment 2 category C3 EN/IEC 61800-3 4...12 kHz shielded motor cable 20 m
Product certifications
CSA

C-Tick

GOST

NOM

UL
Vibration resistance
1 gn EN/IEC 60068-2-6 13...200 Hz

1.5 mm peak to peak EN/IEC 60068-2-6 3...13 Hz drive unmounted on symmetrical DIN rail
Shock resistance
15 gn EN/IEC 60068-2-27 11 ms
Relative humidity
5...95 % without condensation IEC 60068-2-3

5...95 % without dripping water IEC 60068-2-3
Ambient air temperature for storage
-25...70 °C
Ambient air temperature for operation
-10...50 °C protective cover from the top of the drive removed

50...60 °C with current derating 2.2 % per °C
Operating altitude
> 1000...3000 m with current derating 1 % per 100 m

<= 1000 m without derating
Offer Sustainability
RoHS (date code: YYWW)
Schneider Electric declaration of conformity
REACh
Reference not containing SVHC above the threshold
Contractual warranty
Warranty period
18 months
Write Your Own Review
You're reviewing:ATV12HU15M3

   Frequently Asked Questions and Answers


  • What does the Scrolling LEDs mean on the ATV312?

    Issue: What does the scrolling LEDs mean on the ATV312?   Product Line: Altivar 312, Altivar 12   Environment: All serial numbers   Cause: N/A   Resolution: The scrolling LEDs mean the drive is in Local Operation mode.  To switch into Local Programming, push and hold the ESC button for 2s.  Then all three LED's will be flashing at the same time and the programming can be changed.  When programming is finished, push and hold the ESC button again for 2s to en...
    Read more

  • What size speed potentiometer to use on the Schneider Electric VFDs?

    Issue:  What size speed potentiometer to use on Schneider Electric VFDs?   Product Line: Altivar 61, Altivar 71, Altivar 312, Altivar 12, Altivar 212, Altivar 32, Altivar 58   Environment: All serial numbers   Cause: N/A   Resolution: The Schneider Electric VFDs will work with any potentiometer with a rating from 1k Ohms to 10k Ohms.
    Read more

  • What Communication option are standard on the Schneider drives?

    What Communication option are standard on the Schneider drives? Issue: What Communication option are standard on the Schneider drives? Product Line: ALTIVAR 61, ALTIVAR 71, ALTIVAR 312, ALTIVAR 32, ALTIVAR 212, ALTIVAR 12, Environment: All drives all serial number Cause: N/A Resolution : The standard communication protocols are Modbus  on all Schneider Drives.  However, on the ALTIVAR 61, ALTIVAR 71, ALTIVAR 312, and ALTIVAR 32, CanOpen is standard.
    Read more

  • What causes FST on the display of the Altivar drives?

    What causes FST on the display of the Altivar drives? Issue:  What causes FST on the display of the Altivar drives?   Product Line: Altivar 61, Altivar 71, Altivar 312, Altivar 12, Altivar 31, Altivar 58, Altivar 66   Environment: All serial number   Cause: What causes the drive status to show FST?   Resolution: FST is fast stop.   This status happens if a logic input is assigned to FST and the logic input is active. The second option is when the VFD is in a deceleratin...
    Read more

  • What will cause the input current on one phase of a three phase variable speed drive to be lower than the other two phases?

    Issue:  What will cause the input current on one phase of a three phase variable speed drive to be lower than the other two phases? Product Line: ALTIVAR 212, ALTIVAR 21, altivar 61, altivar 71, altivar 312, altivar 12 Environment: All 3 phase VFD Cause: The in current on a single phase is much lower than the other 2 phases. Resolution: To verify if the issue is the VFD or the incoming power, first rotate 2 of the phases on the input of the VFD terminals.  If the problem remains ...
    Read more

User guide
  • file image ATV12 user manual (pdf) download image`
  • file image 1) ATV12 Quick Start annex - SCCR (UL508) (pdf) download image`
  • file image 1) ATV12 Getting Started (pdf) download image`
Catalogue
  • file image Altivar 12 Catalogue EN_Ed 2015-01 (Low resolution PDF) (pdf) download image`
Instruction sheet
  • file image Instruction sheet fan kit VZ3V1301,302 (pdf) download image`
  • file image Instruction Sheet - EMC Plate : VW3A9523,24,25,32,33 (pdf) download image`
  • file image Instruction sheet EMC filter - VW3A4416...419 (pdf) download image`
  • file image Instruction sheet - Braking Resistor - VW3A7723, VW 3A7724 (pdf) download image`
Certificate
  • file image ATV12 UL CERTIFICATE (pdf) download image`
  • file image ATV12 CSA CERTIFICATE (pdf) download image`
  • file image ATV12 EU DECLARATION (pdf) download image`
End of life manual
  • file image ALTIVAR 12 - 0.75 kW, 100V, 1 PH -1.5–2.2 kW, 200V, 1PH, Product End-of-Life Instructions (pdf) download image`
Product environmental
  • file image Product Environmental ProfileAltivar 12Ranges: 0.75 / 100V / 1PH1.5-2.2 kW / 200V / 1PH (pdf) download image`

Dimensions Drawings

Dimensions
Drive without EMC Conformity Kit



Dimensions in mm

b

c

143

131.2

Dimensions in in.

b

c

5.63

5.16

Drive with EMC Conformity Kit



Dimensions in mm

b1

189.3

Dimensions in in.

b1

7.45



Mounting and Clearance

Mounting Recommendations
Clearance for Vertical Mounting



Mounting Type A



Mounting Type B



Remove the protective cover from the top of the drive.

Mounting Type C



Remove the protective cover from the top of the drive.



Connections and Schema

Three-Phase Power Supply Wiring Diagram



A1
Drive
KM1
Contactor (only if a control circuit is needed)
Q1
Circuit breaker


Recommended Schemes
2-Wire Control for Logic I/O with Internal Power Supply



LI1 :
Forward
LI• :
Reverse
A1 :
Drive
3-Wire Control for Logic I/O with Internal Power Supply



LI1 :
Stop
LI2 :
Forward
LI• :
Reverse
A1 :
Drive
Analog Input Configured for Voltage with Internal Power Supply



(1)
2.2 kΩ…10 kΩ reference potentiometer
A1 :
Drive
Analog Input Configured for Current with Internal Power Supply



(2)
0-20 mA 4-20 mA supply
A1 :
Drive
Connected as Positive Logic (Source) with External 24 vdc Supply



(1)
24 vdc supply
A1 :
Drive
Connected as Negative Logic (Sink) with External 24 vdc supply



(1)
24 vdc supply
A1 :
Drive


Performance Curves

Torque Curves



1 :
Self-cooled motor: continuous useful torque (1)
2 :
Force-cooled motor: continuous useful torque
3 :
Transient overtorque for 60 s
4 :
Transient overtorque for 2 s
5 :
Torque in overspeed at constant power (2)
(1)
For power ratings ≤ 250 W, derating is 20% instead of 50% at very low frequencies.
(2)
The nominal motor frequency and the maximum output frequency can be adjusted from 0.5 to 400 Hz. The mechanical overspeed capability of the selected motor must be checked with the manufacturer.


© 2018 Switchboard in a Box. All Rights Reserved. Design & Developed by Shaligram Infotech