VW3A3310D
Modbus TCP communication card - 1 RJ45 - 10/100 Mbps
- Product or component type
- Communication card
- Range compatibility
- Altivar 61
Altivar 71
Altivar 61Q
Altivar 71Q - Communication port protocol
- Modbus TCP
- Product specific application
- For daisy chain mounting
- Connector type
- 1 RJ45
- Transmission rate
- 10 Mbps
100 Mbps - Physical interface
- Ethernet 2
- Web services
- Altivar chart
Altivar viewer
Data editor
E-mail
Ethernet statistics
FDR Agent
IO Scanner
Security
- Exchange mode
- Half duplex and full duplex
- Communication data link
- LLC : IEEE 802.2
MAC : IEEE 802.3 - Communication network type
- IP conforming to RFC791
- Communication transport type
- 8 connections maximum
TCP conforming to RFC793
UDP - Concept
- Transparent Ready class C20
- Web server
- Embedded
- Communication service
- CiA 402 profile
Communication monitoring can be inhibited, adjustable
Diagnostics (08)
FTP
I/O profile
I/O scanning service can be inhibited
Read device identification (43)
Read holding registers (03)
Read input registers (04)
Read/write multiple registers (23)
SNMP
TFTP
Write multiple registers (16)
Write single register (06) - Display type
- 1 LED for 10/100 Mbps (speed)
1 LED for FLT (Ethernet fault)
1 LED for RX (reception)
1 LED for STS (IP address)
1 LED for TX (transmission)
Graphic display terminal for control word received
Graphic display terminal for reference received
Web server - Product weight
- 0.3 kg
- Warranty period
- 18 months
Frequently Asked Questions and Answers
- What supplies the power to vw3a3401 encoder interface card fitted on Altivar 71?
The encoder interface card VW3A3401 uses an internal 5VDC supply from the drive control block. The interface card supplies 5VDC to the encoder RS422 with maximum current available up to 200mA.
Read more - When does the Drive Overheat Fault (OHF) occur in Altivar 71 Drives.
The Drive Overheat Fault (OHF) indicates that the heat sink temperature has crossed the temperature threshold. This is the information from the temperature sensor located on the heat sink, near the transistor module. When the Thermal Heat Dissipation (THD) is greater than 118% it trips in OHF. 118% is approximately 100 Deg Centigrade temperature on the heat sink. The main causes for the occurrence of this fault are: 1. Excessive ambient temperature. (Provide proper air cooling of the control roo...
Read more - Altivar 61/71 what is the recommended corrective action when the motor runs in reverse with a run forward command?
Issue: The motor is running backwards with a forward run command on the drive. Product line: Altivar ATV61 and ATV71 Environment: All models, all serial numbers Cause: The phase rotation is inverted coming out of the drive going to the motor. Resolution: Option 1: To correct the motor rotation swap two motor leads on the drive output terminals. Option 2: Go in the simple start menu 1.1 find output phase rotation change it from ABC to ACB. Refer to the ATV61 and ATV71 programm...
Read more - What does ramp increment mean for the Altivar 61/71?
Issue: What does ramp increment mean for the Altivar 61/71? Product Line: Altivar 61, Altivar 71 Environment: All serial numbers Cause: N/A Resolution: Ramp increment is a parameter that will change the resolution of the listed parameters: see below Inr M [Ramp increment] 0.01 - 0.1 - 1 0.1 0.01 [0.01]: Ramp up to 99.99 seconds 0.1 [0.1]: Ramp up to 999.9 seconds 1 [1]: Ramp up to 9,000 s...
Read more - Will the relay output, assigned to No Drive Fault, change states on a fault if Auto restart is set to yes on VFD?
Issue: Will the relay output, assigned to No Drive Fault, change states on a fault if Auto restart is set to yes? Product Line: Altivar 61 Altivar 71 ATV61 ATV71 Environment: All Cause: Define the No Drive Fault relay relationship with Auto restart function. Resolution: The relay assigned to No Drive Fault will not change states on a fault, if Auto restart is set to YES, until the max restart time is depleted and the fault still exists.
Read more
